{"id":721,"date":"2026-02-13T16:14:15","date_gmt":"2026-02-13T16:14:15","guid":{"rendered":"https:\/\/cartervalves.com\/?p=721"},"modified":"2026-02-13T16:14:17","modified_gmt":"2026-02-13T16:14:17","slug":"valve-markings-rating-and-standards","status":"publish","type":"post","link":"https:\/\/cartervalves.com\/ja\/valve-markings-rating-and-standards\/","title":{"rendered":"\u30d0\u30eb\u30d6\u306e\u30de\u30fc\u30ad\u30f3\u30b0\u3001\u5b9a\u683c\u3001\u898f\u683c\uff1a\u5b8c\u5168\u30ac\u30a4\u30c9"},"content":{"rendered":"\n<p>Buying a valve that \u201cmatches the line size\u201d but fails in service is a costly and avoidable mistake. In practice, most failures trace back to how markings, ratings, and standards were interpreted\u2014often too literally. Body castings and nameplates look authoritative, yet they compress multiple assumptions: material groups, temperature limits, test methods, and acceptance criteria. When any of those assumptions do not match the real service envelope (pressure, temperature, media, cycling, solids, or isolation requirement), the result is premature leakage, unstable torque, or unplanned maintenance.<\/p>\n\n\n\n<figure class=\"wp-block-image aligncenter size-full\"><img fetchpriority=\"high\" decoding=\"async\" width=\"612\" height=\"542\" src=\"https:\/\/cartervalves.com\/wp-content\/uploads\/2026\/02\/136ab1c205917411a8fe36215815d773.png\" alt=\"\" class=\"wp-image-739\" srcset=\"https:\/\/cartervalves.com\/wp-content\/uploads\/2026\/02\/136ab1c205917411a8fe36215815d773.png 612w, https:\/\/cartervalves.com\/wp-content\/uploads\/2026\/02\/136ab1c205917411a8fe36215815d773-300x266.png 300w, https:\/\/cartervalves.com\/wp-content\/uploads\/2026\/02\/136ab1c205917411a8fe36215815d773-14x12.png 14w\" sizes=\"(max-width: 612px) 100vw, 612px\" \/><\/figure>\n\n\n\n<p><strong>Short answer:<\/strong><br>Valve markings summarize size, material, pressure class\/PN, and the standards used to design and test the valve. Ratings are not single numbers; they are material- and temperature-dependent limits defined by the referenced standard. To select correctly, confirm the governing standard and edition, check the pressure\u2013temperature curve for the stated material, and verify the shell\/seat test method and acceptance class. Treat markings as an index into the standard, then validate against your actual operating envelope and project acceptance criteria.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">1) What valve markings usually include (and what each item really means)<\/h2>\n\n\n\n<p>You will typically see some combination of the following on the body or nameplate:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Size<\/strong>: NPS (inch) or DN (metric). This is nominal piping compatibility, not a promise of capacity or low pressure drop.<\/li>\n\n\n\n<li><strong>Pressure class \/ PN<\/strong>: For example <strong>ASME Class 150\/300<\/strong> or <strong>PN16\/PN25<\/strong>. These are rating systems defined by standards.<\/li>\n\n\n\n<li><strong>Material designation<\/strong>: Body and trim materials (ASTM\/EN grades). The <strong>material<\/strong> controls the allowable pressure at temperature.<\/li>\n\n\n\n<li><strong>Standard references<\/strong>: Design\/rating, end connection, and test standards. These define <strong>how<\/strong> the valve is rated and tested.<\/li>\n\n\n\n<li><strong>Manufacturer identifiers<\/strong>: Heat numbers, serial numbers, and logos for traceability.<\/li>\n<\/ul>\n\n\n\n<p><strong>What markings do tell you<\/strong><\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>The <strong>framework<\/strong> (standard + material group) used to establish ratings.<\/li>\n\n\n\n<li>The <strong>interfaces<\/strong> (flange pattern, face-to-face) for piping fit.<\/li>\n\n\n\n<li>The <strong>baseline<\/strong> test method claimed for shell and seat tests.<\/li>\n<\/ul>\n\n\n\n<p><strong>What markings do not tell you<\/strong><\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>The actual <strong>allowable pressure at your operating temperature<\/strong> without consulting the standard\u2019s curve.<\/li>\n\n\n\n<li><strong>Seat wear life<\/strong>, torque margin at temperature, or resistance to erosion\/coking.<\/li>\n\n\n\n<li>Whether a phrase like <strong>\u201czero leakage\u201d<\/strong> refers to a specific test standard and acceptance class.<\/li>\n<\/ul>\n\n\n\n<p><strong>What to verify<\/strong><\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>The <strong>exact standard and edition<\/strong> cited.<\/li>\n\n\n\n<li>The <strong>pressure\u2013temperature curve<\/strong> for the stated material.<\/li>\n\n\n\n<li>The <strong>test standard and acceptance class<\/strong> used for shell and seat tests.<\/li>\n<\/ul>\n\n\n\n<figure class=\"wp-block-image aligncenter size-full\"><img decoding=\"async\" width=\"415\" height=\"665\" src=\"https:\/\/cartervalves.com\/wp-content\/uploads\/2026\/02\/7eeae93d828c52824afcfa50d70453d5.png\" alt=\"\" class=\"wp-image-740\" srcset=\"https:\/\/cartervalves.com\/wp-content\/uploads\/2026\/02\/7eeae93d828c52824afcfa50d70453d5.png 415w, https:\/\/cartervalves.com\/wp-content\/uploads\/2026\/02\/7eeae93d828c52824afcfa50d70453d5-187x300.png 187w, https:\/\/cartervalves.com\/wp-content\/uploads\/2026\/02\/7eeae93d828c52824afcfa50d70453d5-7x12.png 7w\" sizes=\"(max-width: 415px) 100vw, 415px\" \/><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\">2) Ratings are curves, not constants: pressure vs. temperature<\/h2>\n\n\n\n<p>A frequent misunderstanding is to treat \u201cClass 300\u201d or \u201cPN25\u201d as fixed guarantees. In reality, both ASME Class and PN systems are <strong>defined by standards<\/strong> that derate allowable pressure as temperature increases. The curve depends on the <strong>material group<\/strong>.<\/p>\n\n\n\n<p><strong>Practical consequences<\/strong><\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Two valves both marked \u201cClass 300\u201d can have <strong>different allowable pressures<\/strong> at the same temperature if the materials differ.<\/li>\n\n\n\n<li>For <strong>high-temperature services<\/strong> (e.g., FCCU isolation) or <strong>cryogenic duties<\/strong> (e.g., LNG isolation), the material-specific curve and low-temperature impact requirements matter more than the class label.<\/li>\n<\/ul>\n\n\n\n<p><strong>What to verify<\/strong><\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>The <strong>pressure\u2013temperature table\/curve<\/strong> for the exact material grade.<\/li>\n\n\n\n<li>Any <strong>seat or design derating<\/strong> stated by the manufacturer for the service.<\/li>\n\n\n\n<li>Whether your <strong>maximum and minimum<\/strong> operating temperatures both sit within the qualified range.<\/li>\n<\/ul>\n\n\n\n<p>For general references on how rating systems are structured, see the standards bodies themselves (e.g., ASME at https:\/\/www.asme.org and ISO at https:\/\/www.iso.org). Always rely on the project-specified standard and edition rather than secondary summaries.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">3) Understanding the main standards you will encounter<\/h2>\n\n\n\n<p>Markings often cite several standards because each covers a different aspect:<\/p>\n\n\n\n<p>1) <strong>Design and rating standards<\/strong><br>These define how pressure parts are sized and how class\/PN limits are established. In U.S. practice this is typically the ASME framework; in metric practice, EN\/ISO systems are common.<\/p>\n\n\n\n<p>2) <strong>End connection standards<\/strong><br>These define flange dimensions, bolt patterns, and face-to-face dimensions so the valve fits the piping system without adapters.<\/p>\n\n\n\n<p>3) <strong>Test standards<\/strong><br>These define <strong>shell and seat tests<\/strong>: test pressure, duration, and <strong>allowable leakage<\/strong>. Different documents can yield very different acceptance outcomes for the same valve.<\/p>\n\n\n\n<p>Organizations such as ASME (https:\/\/www.asme.org), ISO (https:\/\/www.iso.org), API (https:\/\/www.api.org), and MSS (https:\/\/www.mss-hq.org) publish these documents. The key buyer takeaway is that a marking like \u201cAPI tested\u201d or \u201cISO tested\u201d is incomplete unless the <strong>specific document and acceptance class<\/strong> are stated.<\/p>\n\n\n\n<p><strong>What to verify<\/strong><\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>The <strong>exact document<\/strong> used for testing (not just the organization name).<\/li>\n\n\n\n<li>The <strong>acceptance class<\/strong> for seat leakage.<\/li>\n\n\n\n<li>Any <strong>project-specific additional tests<\/strong> (e.g., low-temperature, high-temperature cycling, or fugitive emissions) required by the specification.<\/li>\n<\/ul>\n\n\n\n<h2 class=\"wp-block-heading\">4) Chart explained: ASME Class vs. PN vs. real operating limits<\/h2>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th>Marking System<\/th><th>What it standardizes<\/th><th>What it guarantees<\/th><th>What it does not guarantee<\/th><\/tr><\/thead><tbody><tr><td><strong><a href=\"# Valve Markings, Ratings &amp; Standards: A Full Guide (Chart Explained)  Buying a valve that \u201cmatches the line size\u201d but fails in service is a costly and avoidable mistake. In practice, most failures trace back to how markings, ratings, and standards were interpreted\u2014often too literally. Body castings and nameplates look authoritative, yet they compress multiple assumptions: material groups, temperature limits, test methods, and acceptance criteria. When any of those assumptions do not match the real service envelope (pressure, temperature, media, cycling, solids, or isolation requirement), the result is premature leakage, unstable torque, or unplanned maintenance.  **Short answer (featured snippet, 60\u2013100 words):**   Valve markings summarize size, material, pressure class\/PN, and the standards used to design and test the valve. Ratings are not single numbers; they are material- and temperature-dependent limits defined by the referenced standard. To select correctly, confirm the governing standard and edition, check the pressure\u2013temperature curve for the stated material, and verify the shell\/seat test method and acceptance class. Treat markings as an index into the standard, then validate against your actual operating envelope and project acceptance criteria.  ---  ## 1) What valve markings usually include (and what each item really means)  You will typically see some combination of the following on the body or nameplate:  - **Size**: NPS (inch) or DN (metric). This is nominal piping compatibility, not a promise of capacity or low pressure drop. - **Pressure class \/ PN**: For example **ASME Class 150\/300** or **PN16\/PN25**. These are rating systems defined by standards. - **Material designation**: Body and trim materials (ASTM\/EN grades). The **material** controls the allowable pressure at temperature. - **Standard references**: Design\/rating, end connection, and test standards. These define **how** the valve is rated and tested. - **Manufacturer identifiers**: Heat numbers, serial numbers, and logos for traceability.  **What markings do tell you** - The **framework** (standard + material group) used to establish ratings. - The **interfaces** (flange pattern, face-to-face) for piping fit. - The **baseline** test method claimed for shell and seat tests.  **What markings do not tell you** - The actual **allowable pressure at your operating temperature** without consulting the standard\u2019s curve. - **Seat wear life**, torque margin at temperature, or resistance to erosion\/coking. - Whether a phrase like **\u201czero leakage\u201d** refers to a specific test standard and acceptance class.  **What to verify** - The **exact standard and edition** cited. - The **pressure\u2013temperature curve** for the stated material. - The **test standard and acceptance class** used for shell and seat tests.  ---  ## 2) Ratings are curves, not constants: pressure vs. temperature  A frequent misunderstanding is to treat \u201cClass 300\u201d or \u201cPN25\u201d as fixed guarantees. In reality, both ASME Class and PN systems are **defined by standards** that derate allowable pressure as temperature increases. The curve depends on the **material group**.  **Practical consequences** - Two valves both marked \u201cClass 300\u201d can have **different allowable pressures** at the same temperature if the materials differ. - For **high-temperature services** (e.g., FCCU isolation) or **cryogenic duties** (e.g., LNG isolation), the material-specific curve and low-temperature impact requirements matter more than the class label.  **What to verify** - The **pressure\u2013temperature table\/curve** for the exact material grade. - Any **seat or design derating** stated by the manufacturer for the service. - Whether your **maximum and minimum** operating temperatures both sit within the qualified range.  For general references on how rating systems are structured, see the standards bodies themselves (e.g., ASME at https:\/\/www.asme.org and ISO at https:\/\/www.iso.org). Always rely on the project-specified standard and edition rather than secondary summaries.  ---  ## 3) Understanding the main standards you will encounter  Markings often cite several standards because each covers a different aspect:  1) **Design and rating standards**      These define how pressure parts are sized and how class\/PN limits are established. In U.S. practice this is typically the ASME framework; in metric practice, EN\/ISO systems are common.  2) **End connection standards**      These define flange dimensions, bolt patterns, and face-to-face dimensions so the valve fits the piping system without adapters.  3) **Test standards**      These define **shell and seat tests**: test pressure, duration, and **allowable leakage**. Different documents can yield very different acceptance outcomes for the same valve.  Organizations such as ASME (https:\/\/www.asme.org), ISO (https:\/\/www.iso.org), API (https:\/\/www.api.org), and MSS (https:\/\/www.mss-hq.org) publish these documents. The key buyer takeaway is that a marking like \u201cAPI tested\u201d or \u201cISO tested\u201d is incomplete unless the **specific document and acceptance class** are stated.  **What to verify** - The **exact document** used for testing (not just the organization name). - The **acceptance class** for seat leakage. - Any **project-specific additional tests** (e.g., low-temperature, high-temperature cycling, or fugitive emissions) required by the specification.  ---  ## 4) Chart explained: ASME Class vs. PN vs. real operating limits  | Marking System | What it standardizes | What it guarantees | What it does not guarantee | |---|---|---|---| | **ASME Class (e.g., 150\/300)** | U.S. design\/rating framework tied to materials | Interface compatibility and a defined rating system | Allowable pressure at your temperature without consulting the curve | | **PN (e.g., 16\/25)** | Metric pressure designation system | Metric compatibility and a nominal pressure family | Material-specific limits at temperature | | **Test references (API\/ISO\/MSS, etc.)** | How shell\/seat tests are run | That a test was performed to that document | Any tighter leakage than the stated acceptance class |  **Buyer checklist for charts** - Ask the vendor for the **actual curve** used in the rating. - Confirm the **material grade** behind the curve. - Confirm the **test acceptance** that defines \u201ctightness\u201d for the project.  ---  ## 5) How markings inform butterfly valve design choice  Markings help you screen options, but **geometry** and **sealing concept** decide long-term performance. Carter Valve provides engineered butterfly valve solutions where standards compliance is the baseline and the design is selected to match the service:  - **High Performance Butterfly Valve**: Typically chosen where pressure class and temperature are within common ranges and repeatable performance with manageable torque is required. - **Triple Offset Butterfly Valve** and **Metal-to-Metal Seated** designs: Applied when temperature, particulates, or cycling demand a geometry that avoids rubbing during seating and controls wear. - **Six-Eccentric Butterfly Valve** (signature line): Used for severe services where predictable shutoff behavior and mechanical stability are required over long campaigns. - **Zero Leakage Isolation** (use only with stated test standards and acceptance criteria): Always specify the **document and class**; the phrase alone is not a guarantee.  For an overview of Carter\u2019s product families and application focus, see https:\/\/cartervalves.com\/. Use that as a starting point, then align the design with your specific service risks.  ---  ## 6) Decision table: from markings to a practical selection direction  | Service condition | What the marking suggests | What you must still verify | Typical design direction* | |---|---|---|---| | Moderate P\/T, clean media | Size, class\/PN, material look adequate | Curve at temperature, test acceptance | High Performance Butterfly Valve | | Elevated temperature | Material and class\/PN are critical | Derated allowable pressure, seat concept | Triple Offset or Metal-to-Metal | | Severe isolation, solids, or coking risk | Test standard is listed | Leakage class, wear pattern, cycling stability | Six-Eccentric Butterfly Valve | | Cryogenic duty | Material and class\/PN are shown | Low-temperature impact, cold leakage criteria | Qualified cryogenic design |  \\*Final choice must be confirmed against the full operating envelope and project acceptance criteria.  ---  ## 7) Niche but important topics buyers often overlook  **a) Edition control of standards**   Ratings and acceptance criteria can change between editions. Always record the **edition year** on the datasheet and in the purchase order.  **b) Differential pressure vs. shutoff pressure**   Markings do not distinguish between **line pressure** and **shutoff differential pressure** across the disc. Actuator sizing and seat stress depend on the latter.  **c) Torque at temperature**   Cold shop tests do not reveal **hot torque**. Ask how torque was estimated or tested at operating temperature, especially for metal-seated designs.  **d) Thermal expansion and alignment**   At high temperature, body and shaft growth can change alignment and contact stress. This is a design topic, not a marking, but it affects long-term leakage.  **e) Media compatibility beyond corrosion tables**   Coking, polymerizing, or particle-laden services can defeat otherwise compliant ratings. Ask about **field experience** or **qualification tests** for similar media.  ---  ## 8) Selection checklist (use before you approve a datasheet)  - [ ] Governing **design\/rating standard** identified and edition recorded   - [ ] **Pressure\u2013temperature curve** documented for the exact material grade   - [ ] **End connection standard** matches the piping specification   - [ ] **Test standard** and **acceptance class** defined for shell and seat tests   - [ ] **Operating envelope** listed: min\/max P, min\/max T, media, cycles, solids   - [ ] **Design geometry** chosen to match wear, temperature, and isolation needs   - [ ] **Actuator sizing basis** stated for maximum differential pressure at temperature  ---  ## 9) Commissioning &amp; acceptance checklist  - [ ] Nameplate **matches the approved datasheet** (size, class\/PN, material, standard)   - [ ] **Shell and seat tests** witnessed or documented per the specified document   - [ ] **Torque and actuator margins** verified against worst-case conditions   - [ ] **Installation orientation** and clearances confirmed   - [ ] **Documentation pack** complete (traceability, material certificates, test reports)  ---  ## 10) Common pitfalls\u2014and how to avoid them  - **Assuming class\/PN equals allowable pressure at any temperature.**     *Fix:* Always consult the standard\u2019s curve for the stated material.  - **Accepting \u201czero leakage\u201d without a test reference.**     *Fix:* Specify the **document and acceptance class** that define tightness.  - **Ignoring material grade differences inside the same family.**     *Fix:* Record the **exact grade** and condition used for the rating.  - **Sizing actuators from cold, clean-service torque only.**     *Fix:* Require a **hot, worst-case differential pressure** sizing basis.  ---  ## Conclusion: practical next steps  Valve markings and ratings are essential\u2014but they are **indexes into standards**, not performance guarantees. Start by confirming the governing standard and edition, check the material-specific pressure\u2013temperature limits, and lock down the test method and acceptance class. Then match the **design geometry** to your real service risks (temperature, solids, cycling, isolation requirement). If your application involves severe service, high temperature, or cryogenic isolation, share your full operating envelope and acceptance criteria for a brief selection review at https:\/\/cartervalves.com\/ to align compliance, design, and long-term reliability before purchase.\">ASME Class (e.g., 150\/300)<\/a><\/strong><\/td><td>U.S. design\/rating framework tied to materials<\/td><td>Interface compatibility and a defined rating system<\/td><td>Allowable pressure at your temperature without consulting the curve<\/td><\/tr><tr><td><strong>PN (e.g., 16\/25)<\/strong><\/td><td>Metric pressure designation system<\/td><td>Metric compatibility and a nominal pressure family<\/td><td>Material-specific limits at temperature<\/td><\/tr><tr><td><strong>Test references (<a href=\"https:\/\/www.api.org\/\" target=\"_blank\" rel=\"noopener\">API<\/a>\/<a href=\"https:\/\/www.iso.org\/standards.html\" target=\"_blank\" rel=\"noopener\">ISO<\/a>\/<a href=\"https:\/\/msshq.org\/\" data-type=\"link\" data-id=\"https:\/\/msshq.org\/\" target=\"_blank\" rel=\"noopener\">MSS<\/a>, etc.)<\/strong><\/td><td>How shell\/seat tests are run<\/td><td>That a test was performed to that document<\/td><td>Any tighter leakage than the stated acceptance class<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p><strong>Buyer checklist for charts<\/strong><\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Ask the vendor for the <strong>actual curve<\/strong> used in the rating.<\/li>\n\n\n\n<li>Confirm the <strong>material grade<\/strong> behind the curve.<\/li>\n\n\n\n<li>Confirm the <strong>test acceptance<\/strong> that defines \u201ctightness\u201d for the project.<\/li>\n<\/ul>\n\n\n\n<h2 class=\"wp-block-heading\">5) How markings inform butterfly valve design choice<\/h2>\n\n\n\n<p>Markings help you screen options, but <strong>geometry<\/strong> and <strong>sealing concept<\/strong> decide long-term performance.<a href=\"https:\/\/cartervalves.com\/\" data-type=\"link\" data-id=\"https:\/\/cartervalves.com\/\"> Carter Valve<\/a> provides engineered butterfly valve solutions where standards compliance is the baseline and the design is selected to match the service:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><a href=\"https:\/\/cartervalves.com\/product\/high-performance-double-offset-butterfly-valve\/\" data-type=\"product\" data-id=\"452\">High-Performance Double Offset Butterfly Valve<\/a>: Typically chosen where pressure class and temperature are within common ranges and repeatable performance with manageable torque is required.<\/li>\n\n\n\n<li><strong>Triple Offset Butterfly Valve<\/strong> and <strong>Metal-to-Metal Seated<\/strong> designs: Applied when temperature, particulates, or cycling demand a geometry that avoids rubbing during seating and controls wear.<\/li>\n\n\n\n<li><strong>Six-Eccentric Butterfly Valve<\/strong> (signature line): Used for severe services where predictable shutoff behavior and mechanical stability are required over long campaigns.<br>More reading about<a href=\"https:\/\/cartervalves.com\/carterus-six-eccentric-butterfly-valve\/\"> <strong>Six-Eccentric Butterfly Valve<\/strong><\/a> \u3002<\/li>\n\n\n\n<li><strong>Zero Leakage Isolation<\/strong> (use only with stated test standards and acceptance criteria): Always specify the <strong>document and class<\/strong>; the phrase alone is not a guarantee.<\/li>\n<\/ul>\n\n\n\n<p>For an overview of Carter\u2019s product families and application focus, see https:\/\/cartervalves.com\/. Use that as a starting point, then align the design with your specific service risks.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">6) Decision table: from markings to a practical selection direction<\/h2>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th>Service condition<\/th><th>What the marking suggests<\/th><th>What you must still verify<\/th><th>Typical design direction*<\/th><\/tr><\/thead><tbody><tr><td>Moderate P\/T, clean media<\/td><td>Size, class\/PN, material look adequate<\/td><td>Curve at temperature, test acceptance<\/td><td>High Performance Butterfly Valve<\/td><\/tr><tr><td>Elevated temperature<\/td><td>Material and class\/PN are critical<\/td><td>Derated allowable pressure, seat concept<\/td><td>Triple Offset or Metal-to-Metal<\/td><\/tr><tr><td>Severe isolation, solids, or coking risk<\/td><td>Test standard is listed<\/td><td>Leakage class, wear pattern, cycling stability<\/td><td>Six-Eccentric Butterfly Valve<\/td><\/tr><tr><td>Cryogenic duty<\/td><td>Material and class\/PN are shown<\/td><td>Low-temperature impact, cold leakage criteria<\/td><td>Qualified cryogenic design<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p>*Final choice must be confirmed against the full operating envelope and project acceptance criteria.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">7) Niche but important topics buyers often overlook<\/h2>\n\n\n\n<p><strong>a) Edition control of standards<\/strong><br>Ratings and acceptance criteria can change between editions. Always record the <strong>edition year<\/strong> on the datasheet and in the purchase order.<\/p>\n\n\n\n<p><strong>b) Differential pressure vs. shutoff pressure<\/strong><br>Markings do not distinguish between <strong>line pressure<\/strong> and <strong>shutoff differential pressure<\/strong> across the disc. Actuator sizing and seat stress depend on the latter.<\/p>\n\n\n\n<p><strong>c) Torque at temperature<\/strong><br>Cold shop tests do not reveal <strong>hot torque<\/strong>. Ask how torque was estimated or tested at operating temperature, especially for metal-seated designs.<\/p>\n\n\n\n<p><strong>d) Thermal expansion and alignment<\/strong><br>At high temperature, body and shaft growth can change alignment and contact stress. This is a design topic, not a marking, but it affects long-term leakage.<\/p>\n\n\n\n<p><strong>e) Media compatibility beyond corrosion tables<\/strong><br>Coking, polymerizing, or particle-laden services can defeat otherwise compliant ratings. Ask about <strong>field experience<\/strong> or <strong>qualification tests<\/strong> for similar media.<\/p>\n\n\n\n<figure class=\"wp-block-image size-full\"><img decoding=\"async\" width=\"900\" height=\"600\" src=\"https:\/\/cartervalves.com\/wp-content\/uploads\/2026\/02\/\u751f\u6210\u7279\u5b9a\u5c3a\u5bf8\u53d8\u6e05\u6670\u7684\u56fe\u724733.png\" alt=\"\" class=\"wp-image-729\" srcset=\"https:\/\/cartervalves.com\/wp-content\/uploads\/2026\/02\/\u751f\u6210\u7279\u5b9a\u5c3a\u5bf8\u53d8\u6e05\u6670\u7684\u56fe\u724733.png 900w, https:\/\/cartervalves.com\/wp-content\/uploads\/2026\/02\/\u751f\u6210\u7279\u5b9a\u5c3a\u5bf8\u53d8\u6e05\u6670\u7684\u56fe\u724733-300x200.png 300w, https:\/\/cartervalves.com\/wp-content\/uploads\/2026\/02\/\u751f\u6210\u7279\u5b9a\u5c3a\u5bf8\u53d8\u6e05\u6670\u7684\u56fe\u724733-768x512.png 768w, https:\/\/cartervalves.com\/wp-content\/uploads\/2026\/02\/\u751f\u6210\u7279\u5b9a\u5c3a\u5bf8\u53d8\u6e05\u6670\u7684\u56fe\u724733-18x12.png 18w\" sizes=\"(max-width: 900px) 100vw, 900px\" \/><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\">8) Selection checklist (use before you approve a datasheet)<\/h2>\n\n\n\n<ul class=\"wp-block-list\">\n<li>[ ] Governing <strong>design\/rating standard<\/strong> identified and edition recorded<\/li>\n\n\n\n<li>[ ] <strong>Pressure\u2013temperature curve<\/strong> documented for the exact material grade<\/li>\n\n\n\n<li>[ ] <strong>End connection standard<\/strong> matches the piping specification<\/li>\n\n\n\n<li>[ ] <strong>Test standard<\/strong> and <strong>acceptance class<\/strong> defined for shell and seat tests<\/li>\n\n\n\n<li>[ ] <strong>Operating envelope<\/strong> listed: min\/max P, min\/max T, media, cycles, solids<\/li>\n\n\n\n<li>[ ] <strong>Design geometry<\/strong> chosen to match wear, temperature, and isolation needs<\/li>\n\n\n\n<li>[ ] <strong>Actuator sizing basis<\/strong> stated for maximum differential pressure at temperature<\/li>\n<\/ul>\n\n\n\n<h2 class=\"wp-block-heading\">9) Commissioning &amp; acceptance checklist<\/h2>\n\n\n\n<ul class=\"wp-block-list\">\n<li>[ ] Nameplate <strong>matches the approved datasheet<\/strong> (size, class\/PN, material, standard)<\/li>\n\n\n\n<li>[ ] <strong>Shell and seat tests<\/strong> witnessed or documented per the specified document<\/li>\n\n\n\n<li>[ ] <strong>Torque and actuator margins<\/strong> verified against worst-case conditions<\/li>\n\n\n\n<li>[ ] <strong>Installation orientation<\/strong> and clearances confirmed<\/li>\n\n\n\n<li>[ ] <strong>Documentation pack<\/strong> complete (traceability, material certificates, test reports)<\/li>\n<\/ul>\n\n\n\n<h2 class=\"wp-block-heading\">10) Common pitfalls\u2014and how to avoid them<\/h2>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Assuming class\/PN equals allowable pressure at any temperature.<\/strong><br><em>Fix:<\/em> Always consult the standard\u2019s curve for the stated material.<\/li>\n\n\n\n<li><strong>Accepting \u201czero leakage\u201d without a test reference.<\/strong><br><em>Fix:<\/em> Specify the <strong>document and acceptance class<\/strong> that define tightness.<br><a href=\"https:\/\/cartervalves.com\/bi-directional-zero-leakage-what-it-means-and-why-it-matters-in-severe-service\/\">More reading about the importance of <strong>\u201czero leakage\u201d<\/strong><\/a><\/li>\n\n\n\n<li><strong>Ignoring material grade differences inside the same family.<\/strong><br><em>Fix:<\/em> Record the <strong>exact grade<\/strong> and condition used for the rating.<\/li>\n\n\n\n<li><strong>Sizing actuators from cold, clean-service torque only.<\/strong><br><em>Fix:<\/em> Require a <strong>hot, worst-case differential pressure<\/strong> sizing basis.<\/li>\n<\/ul>\n\n\n\n<h2 class=\"wp-block-heading\">Conclusion: practical next steps<\/h2>\n\n\n\n<p>Valve markings and ratings are essential\u2014but they are <strong>indexes into standards<\/strong>, not performance guarantees. Start by confirming the governing standard and edition, check the material-specific pressure\u2013temperature limits, and lock down the test method and acceptance class. Then match the <strong>design geometry<\/strong> to your real service risks (temperature, solids, cycling, isolation requirement). If your application involves severe service, high temperature, or cryogenic isolation, share your full operating envelope and acceptance criteria for a brief selection review at <a href=\"https:\/\/cartervalves.com\/contact\/\" data-type=\"page\" data-id=\"18\">Carter<\/a> to align compliance, design, and long-term reliability before purchase.<\/p>\n\n\n\n<p><\/p>\n","protected":false},"excerpt":{"rendered":"<p>Buying a valve that \u201cmatches the line size\u201d but fails in service is a costly and avoidable mistake. In practice, most failures trace back to how markings, ratings, and standards were interpreted\u2014often too literally. Body castings and nameplates look authoritative, yet they compress multiple assumptions: material groups, temperature limits, test methods, and acceptance criteria. When any of those assumptions do not match the real service envelope (pressure, temperature, media, cycling, solids, or isolation requirement), the result is premature leakage, unstable torque, or unplanned maintenance. Short answer:Valve markings summarize size, material, pressure class\/PN, and the standards used to design and test the valve. Ratings are not single numbers; they are material- [&hellip;]<\/p>\n","protected":false},"author":1,"featured_media":725,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_acf_changed":false,"footnotes":""},"categories":[1],"tags":[],"class_list":["post-721","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-blog"],"acf":[],"_links":{"self":[{"href":"https:\/\/cartervalves.com\/ja\/wp-json\/wp\/v2\/posts\/721","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/cartervalves.com\/ja\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/cartervalves.com\/ja\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/cartervalves.com\/ja\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/cartervalves.com\/ja\/wp-json\/wp\/v2\/comments?post=721"}],"version-history":[{"count":1,"href":"https:\/\/cartervalves.com\/ja\/wp-json\/wp\/v2\/posts\/721\/revisions"}],"predecessor-version":[{"id":741,"href":"https:\/\/cartervalves.com\/ja\/wp-json\/wp\/v2\/posts\/721\/revisions\/741"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/cartervalves.com\/ja\/wp-json\/wp\/v2\/media\/725"}],"wp:attachment":[{"href":"https:\/\/cartervalves.com\/ja\/wp-json\/wp\/v2\/media?parent=721"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/cartervalves.com\/ja\/wp-json\/wp\/v2\/categories?post=721"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/cartervalves.com\/ja\/wp-json\/wp\/v2\/tags?post=721"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}